Compatible Washing Machine Carbon Brushes for Indesit Hotpoint Ariston - C00196539

C00196539 Compatible Washing Machine Motor Carbon Brushes – Fits Indesit, Hotpoint, Ariston and More (Pack of 2)

A compatible replacement carbon brush set comparing to Indesit/Hotpoint reference C00196539. Supplied as a pair (2 brushes), these laminated carbon brushes are designed for use with Indesco and Welling 3rd Type motors fitted to a wide range of Indesit, Hotpoint, and Ariston washing machines. Also referenced as CBN9191, CAR73, 12-AR-07 and MER047317. If your washing machine stops mid-cycle, fails to spin, or runs intermittently, worn carbon brushes are one of the most common causes and one of the most cost-effective repairs.

Product Details

• Product Type: Washing Machine Motor Carbon Brush Set
• Main Part Number / MPN: C00196539
• Alternative / Cross References: CBN9191, CAR73, 12-AR-07, MER047317
• Motor Type: Indesco motor / Welling 3rd Type motor
• Brush Dimensions: 12mm × 5mm × 31mm
• Terminal Size: 6.3mm
• Brush Slope: Left to Right (L to R)
• Material: Laminated carbon with flame-retardant plastic brush holders
• Appliance Types: Washing Machine, Washer Dryer
• Brand Compatibility: Indesit, Hotpoint, Ariston, Creda, New World, Philco, Scholtes
• Part Type: Compatible Replacement
• Pack Includes: 2 × Carbon Brushes (pair)

What This Part Does

Carbon brushes are small blocks of carbon that press against the spinning commutator on the washing machine motor's armature. They conduct electrical current into the rotating part of the motor, enabling the motor to spin the drum. As the brushes wear down over time — they are a consumable contact part — they become too short to maintain reliable contact with the commutator. This causes the motor to run intermittently, stop mid-cycle, or fail to spin the drum at all. Replacing worn carbon brushes is one of the most common and cost-effective washing machine repairs and restores the motor to full working order.

These brushes use laminated carbon rather than block carbon, which provides better heat conduction and longer service life.

Common Fault Symptoms

• Washing machine stops mid-cycle (especially during the spin cycle)
• Drum fails to spin or spins erratically
• Machine starts but cuts out shortly after beginning a cycle
• Burning smell from the motor area (under the machine)
• Machine makes no noise when a spin is expected — motor not running
• Drum turns slowly or with reduced power
• Fault codes relating to motor or spin failure appearing on the display

Known Compatible Brands & Models

How to Replace Washing Machine Carbon Brushes

Replacing carbon brushes requires partial disassembly of the washing machine to access the motor. You will need to remove the rear panel (or front panel depending on the model), disconnect the motor wiring, and slide out the brush holders from the sides of the motor. The old brushes are pulled out and the new brushes inserted in their place, with the spring behind the brush applying the contact pressure. Both brushes should always be replaced at the same time — fitting only one new brush alongside a worn brush leads to uneven wear and premature failure. Reassemble in reverse order.

Repair Difficulty

Moderate — suitable for a competent DIY repairer with basic tools. Accessing the motor requires removing the back panel of the machine and disconnecting electrical connectors. Always isolate the appliance from the mains before working on it.

Typical Tools Required

• Torx screwdriver (T20 or T25) or flat-head / Phillips screwdriver depending on model
• Spanner or socket set (to release motor mounting bolts where fitted)
• Multimeter (optional — for testing motor continuity)

Description

Compatible replacement washing machine motor carbon brush set comparing to Indesit/Hotpoint reference C00196539. Also referenced as CBN9191, CAR73, 12-AR-07 and MER047317. Supplied as a pair (2 brushes). Specifications: 12mm × 5mm × 31mm, 6.3mm terminals, Left to Right (L to R) brush slope, laminated carbon construction, flame-retardant plastic brush holders. For use with Indesco and Welling 3rd Type motors fitted to Indesit, Hotpoint, Ariston, Creda, New World, Philco and Scholtes washing machines and washer dryers.

These brands are all part of the Whirlpool Group and share common motor parts across their appliance ranges. This is a compatible replacement — it is not a genuine or OEM part. Please compare the brush shape and dimensions to your original brushes using the product photos before ordering to confirm the slope direction and terminal type match your machine's motor.